Visonic PowerMax10 Especificaciones Pagina 12
- Pagina / 78
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
D-302756 11
To Configure Permissions for System Reset after an Alarm Event
1. Make sure the system is disarmed and then press the button
repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".
2.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
The screen will now prompt you to enter your installer code.
OKI
3.
Enter your Installer Code.
2
CODE
4. Press the or button repeatedly and select the [DEFINE PANEL]
option.
or
5. When the PowerMax10-G2 display reads [DEFINE PANEL], press
OKI
The PowerMax10-G2 display will read [01:ENTRY DELAY 1].
OKI
6.
When the PowerMax10-G2 display reads [01:ENTRY DELAY 1], press
the
or button repeatedly until the display will read [25:RESET
OPTIONS].
or
7.
Press
OKI
and make the selection and then press
OKI
to confirm.
OKI
The PowerMax10-G2 display reverts to "
25:RESET OPTION
" and a "Happy Tune"
☺ sounds.
You can now press the or button to program any other menu in
"
DEFINE PANEL
" or press the button to take you to "
<OK> TO EXIT
".
☺
4.3.6 Configuring a Duress Code
A duress alarm (ambush) message can be sent to the Monitoring Station if the user is forced to disarm the system under
violence or menace. To initiate a duress message, the user must disarm the system with the duress code (2580 by default).
Here you can change the code digits or enter "0000" to disable the duress feature. The system does not allow the user to
program the duress code saved in this memory location as an existing user code.
Note: Duress Code is not applicable in the UK.
To Configure a Duress Code
1. Make sure the system is disarmed and then press the button
repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".
2. When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
The screen will now prompt you to enter your installer code.
OKI
3.
Enter your Installer Code.
CODE
4. Press the or button repeatedly and select the [DEFINE PANEL]
option.
or
5. When the PowerMax10-G2 display reads [DEFINE PANEL], press
OKI
The PowerMax10-G2 display will read [01:ENTRY DELAY 1].
OKI
6.
When the PowerMax10-G2 display reads [01:ENTRY DELAY 1], press
the
or button repeatedly until the display will read [23:DURESS].
or
7.
Press
OKI
, change the code or enter 0000 to disable the duress function
and then press
OKI
to confirm.
OKI
25:RESET OPTION
2
5:RESET OPTION
0
1:ENTRY DELAY 1
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
D
EFINE PA
N
EL
2
3:DURESS
0
1:ENTRY DELAY 1
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
D
EFINE PANEL
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Visonic PowerMax10
(76 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.196 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales