Visonic PowerMax10 Especificaciones Pagina 41
- Pagina / 78
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
40 D-302756
CODE
4. Press the or button repeatedly and select the [DEFINE PANEL]
option.
or
5. When the PowerMax10-G2 display reads [DEFINE PANEL], press
OKI
The PowerMax10-G2 display will read [01:ENTRY DELAY 1].
OKI
6.
When the PowerMax10-G2 display reads [01:ENTRY DELAY 1], press
the
or button repeatedly until the display will read [06:ALARM
CANCEL].
or
7.
Press
OKI
and make the selection and then press
OKI
to confirm.
The PowerMax10-G2 display will revert to [06:ALARM CANCEL].
OKI
SELECT OPTION
OKI
You can now press the or button to program any other menu in
"
DEFINE PANEL
" or press the button to take you to "
<OK> TO EXIT
".
4.7.5 Configuring Power Failure Threshold Period
Here you determine the time interval between AC power failure occurrence and the failure reporting.
Options: 5 minutes (default), 30 minutes, 60 minutes or 180 minutes.
Note: To comply with EN requirements, set to 60 min. max.
To Configure the Power Failure Threshold Period
1. Make sure the system is disarmed and then press the button
repeatedly until the PowerMax10-G2 display reads "INSTALLER MODE".
2.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
The screen will now prompt you to enter your installer code.
OKI
3.
Enter your Installer Code.
CODE
4. Press the or button repeatedly and select the [DEFINE PANEL]
option.
or
5. When the PowerMax10-G2 display reads [DEFINE PANEL], press
OKI
The PowerMax10-G2 display will read [01:ENTRY DELAY 1].
OKI
6.
When the PowerMax10-G2 display reads [01:ENTRY DELAY 1], press
the
or button repeatedly until the display will read [34:AC FAIL
REP].
or
7.
Press
OKI
and make the selection and then press
OKI
to confirm.
The PowerMax10-G2 display will revert to [34:AC FAIL REP].
OKI
SELECT OPTION
OKI
You can now press the or button to program any other menu in
"
DEFINE PANEL
" or press the button to take you to "
<OK> TO EXIT
".
4.7.6 Configuring Abort Time
Here you select the length of time allowed by the system to abort an alarm (not applicable to alarms from FIRE, 24H SILENT,
EMERGENCY, GAS, FLOOD and TEMPERATURE zones). The PowerMax10-G2 is programmed to provide an “abort interval”
that starts upon detection of an event. During this interval, the buzzer sounds a warning but the siren remains inactive and the
alarm is not reported. If the user disarms the system within the allowed abort interval, the alarm is aborted.
3
4:AC FAIL REP
0
6:ALARM CANCEL
3
4:
A
C FAIL REP
0
1:ENTRY DELAY 1
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
D
EFINE PANEL
0
6:
A
LARM CANCEL
0
1:ENTRY DELAY 1
D
EFINE PANEL
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Visonic PowerMax10
(76 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales