Visonic POWERART Guía de usuario descargar pdf (Pagina 17)

DE5458U 17

bypassed zones, in ascending numerical order. When

done, clicking <HOME> will get you back to SHOW

BYPASS and clicking <AWAY> will get you back to <OK>

TO EXIT.

7.5 Recalling the Last Bypass Scheme

Arming the alarm system with several zones in the

bypassed state is in fact "partial arming". An identical

partial arming may be repeated by recalling the last

bypassing scheme (that was suspended and memorized

upon disarming the system).

Having entered your user code successfully (see Para.

7.2), the display will read:

SET BYPASS

Click <NEXT> twice to change the display into:

RECALL BYPASS

At this point proceed as follows:

Action Resultant Display Sound

☞

<OK> TO RECALL

☞

RECALL BYPASS

☺

You may now select any other item on the USER

SETTINGS menu or quit programming by clicking <AWAY>.

When <OK> TO EXIT is displayed - click <OK>.

7.6 Programming the “Follow-me”

Telephone Number

Having entered your Master Code successfully (see Para.

7.2), the display will read:

SET PHONE NUMBER

Please note that the 1

, 2

and 3

private telephone

numbers are programmed by the installer. You are allowed

to program the 4

(“follow-me”) number as follows:

Action Resultant Display Sound

☞

[Tel. No.]

XXXXXXXXX

☞

XXXXXXXXX

☞

SET PHONE NUMBER

☺

You may now switch to any other item on the USER

SETTINGS menu or quit programming by clicking <NEXT>

until <OK> TO EXIT is displayed and then clicking <OK>.

7.7 Setting the User Codes

Having entered your Master Code successfully (see Para.

7.2), click <NEXT> until the display reads:

SET USER CODES

Please note that:

User Code 1 replaces the factory default master code,

and should be assigned to the master user of the system.

This code can not be erased.

User Codes 2, 3 and 4 can be assigned to additional

users - family members, co-workers etc.

Codes 5 through 8 are assigned to “Latchkey Users” (see

Para. 2.9 for explanation of the latchkey mode).

CAUTION! Code “0000” is not valid! Do not use it.

Note: The duress code set by the installer (2580 by

default) cannot be selected as a normal user code. Any

attempt to program it will be rejected by the PowerArt™.

To program the codes, proceed as follows:

Action Resultant Display Sound

☞

user code1

____

☞

user code1:

000

☞

[4-digit code]

(e.g. 6854)

user code1:685

☞

user code1:6854

☞

user code2

☺

Continue the same way up to Code 8.

☞

user code8:5537

☞

SET USER CODES

☺

You may now select any other item on the USER

SETTINGS menu or quit programming by clicking <AWAY>.

When <OK> TO EXIT is displayed - click <OK>.

7.8 Setting the Voice Options

Remember: Voice prompts are heard over the built-in

loudspeaker subject to two conditions:

- The voice option is enabled as shown below

- The loudspeaker is enabled by pressing the “7” key

(see Para. 3.3)

The following procedure allows you to select one of two

options:

• Enable prompts: Voice announcements

• Disable prompts: No voice announcements

The presently programmed option will be shown, with a

dark selection box (

) at the far right of the display. You

may view the other option (that does not have a dark box

at the far right) by clicking <NEXT>. A dark box will appear

if you click <OK> while the other option is displayed.

To set the voice option, proceed as follows:

Having entered your Master Code successfully (see Para.

7.2), click the <NEXT> button until the display reads:

SET VOICE OPTION

From here, proceed as follows:

Action Resultant Display Sound

☞

enable prompts

(if this is the current option)

If not satisfied -

☞

disable prompts

If satisfied -

☞

disable prompts

☞

SET VOICE OPTION

☺

You may now select any other item on the USER

SETTINGS menu or quit programming by clicking <AWAY>.

When <OK> TO EXIT is displayed - click <OK>.

7.9 Setting the Clock

Having entered your Master Code successfully (see Para.

7.2), click <NEXT> until the display reads:

TIME HH:MM A

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 23 24

Comentarios a estos manuales

Sin comentarios

Visonic POWERART Guía de usuario Pagina 17

Comentarios a estos manuales

Relacionado con productos y manuales para Monóxido de carbono (co) detectores Visonic POWERART