Visonic PowerMax10 Especificaciones Pagina 10
- Pagina / 78
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
D-302756 9
3.
Enter your Installer Code.
CODE
4. When the PowerMax10-G2 display reads [NEW INSTL CODE], press
OKI
.
OKI
The PowerMax10-G2 display will read [NEW MASTER CODE].
Note: The menu displays within the dashed box appear only if the control panel
includes the Master Installer Code.
5. Press the button.
6.
When the PowerMax10-G2 display reads [NEW INST. CODE], press
OKI
.
OKI
7.
Enter the new 4-digit Installer Code (8888 or 9999) at the position of the blinking
cursor and then press
OKI
.
OKI
The PowerMax10-G2 display reads [
NEW INST. CODE
] and a "Happy Tune" ☺
sounds to confirm the new Installer Code.
If your system uses MASTER CODE, you should proceed to setting the MASTER
INSTALLER code in section 4.3.2 by pressing the button, or press the
button to take you to "
<OK> TO EXIT
".
☺
Note: Installer Code should never be programmed as “0000”. Doing so will lock the user out of the installer menu!
4.3.2 Setting the Master Installer Code
For PowerMax10-G2 with MASTER INSTALLER code, set a new INSTALLER code as described in section 4.3.1 "Setting a
New Installer Code" and set the MASTER INSTALLER code as described in this section.
Note: For Control Panel that has installer code & master installer code, the following functions are available only if the
MASTER INSTALLER code is entered:
• PSTN/GSM RCVR1
• RCVR 1 ACCOUNT#
• PSTN/GSM RCVR2
• RCVR 2 ACCOUNT#
• PSTN RPRT FORMAT
• 4/2 PLS RATE
• REPORT EVENTS
• RPRT CNFRM ALRM
• SEND 2WV CODE
• VOICE Monitoring Station.
• RINGBACK TIME
• PSTN RPRT RETRY
• GSM RPRT RETRY
• MAST. DL CODE
By using the master installer code, the menu enables changing both master installer code and installer code.
By using the installer code, the menu enables changing the installer code only.
B. To Set a New Master Installer Code
1. Make sure the system is disarmed and then press the button repeatedly
until the PowerMax10-G2 display reads "INSTALLER MODE".
2.
When the PowerMax10-G2 display reads [INSTALLER MODE], press
OKI
.
OKI
The screen will now prompt you to enter your installer code.
∗
3.
Enter your Installer Code.
CODE
4. When the PowerMax10-G2 display reads [NEW INSTL CODE], press
OKI
.
OKI
The PowerMax10-G2 display will read [NEW MASTER CODE].
5. Press
OKI
.
OKI
6.
Enter the new 4-digit Installer Code at the position of the blinking cursor and
then press
OKI
.
OKI
N
EW MASTER CODE
MASTER CODE 999
E
NTER CODE:
INSTALLER MODE
R
EADY 00:00
N
EW INSTL CODE
NEW INST. CODE
INST. CODE
8
88
N
EW MASTER CODE
NEW INST. CODE
N
EW INSTL CODE
- PowerMax10 1
- PowerMax10-G2 2
- 2.5 Physical Properties 5
- 3. INSTALLATION 5
- 3.2 System Planning & 7
- Programming 7
- 3.3 Mounting the Unit 7
- 3.4.1 GSM Installation 8
- 3.4.2 PowerLink Installation 8
- 4. PROGRAMMING 9
- 4.1 General Guidance 9
- 4.2 Navigation 9
- NEW INST. CODE 10
- <OK> TO EXIT 10
- NEW MASTER CODE 11
- 36:USER PERMIT 11
- DEFINE PANEL 11
- 25:RESET OPTION 12
- 4.4 Zones / Devices 13
- SAME Dev 15
- EXIT Enrollment 15
- ADD NEW DEVICES 15
- NEXT device 15
- 4.4.2.4 Locations 16
- 4.4.3 Adding Wired Zones 17
- Z01:Motion Sens] 18
- <OFF> to delete] 18
- <OFF> to delete 18
- Z01:Motion Sens 18
- 4.5 Siren Configuration 20
- AREA CODE 23
- GPRS REPORT 26
- 1st RPRT METHOD 27
- RCVR 1 ACCOUNT# 28
- PSTN/GSM RCVR1 29
- PSTN RPRT RETRY 31
- AUTO TEST TIME 32
- PSTN UP/DOWN 34
- REPORT EVENTS 35
- 36
- 4th private tel#] 37
- SMS REPORT TEL# 38
- <OK> 38
- 1st private tel# 38
- 4.10 DEFINE CUSTOM LOCATIONS 54
- 5 DIAGNOSTIC TEST 62
- 5.1 Testing Devices 63
- NO DEVICES 66
- LAN RESET OPTION 66
- WL DEVICES 68
- 7. MAINTENANCE 69
- 7.1 Handling System Troubles 69
- 7.4 Fuse Replacement 70
- 7.6 Restore Factory Defaults 70
- 7.7 Viewing Serial Number 71
- 8 READING THE EVENT LOG 71
- 8.1 Reading the Event Log 71
- A1. Detector Deployment Plan 72
- A2. Keyfob Transmitter List 73
- APPENDIX B. Event Codes 74
- B1. Contact ID Event Codes 74
- B2. SIA Event Codes 74
- B3. 4/2 Event Codes 74
- APPENDIX C. Glossary 75
- Industry Canada Declaration 77
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Visonic PowerMax10
(76 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.260 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales